A switch adapted battery operated toy is a toy that has been modified so that a child with a disability can press a switch and activate the toy. The necessary modifications are easy for most adults with just a few tools and supplies from your local electronics store or some hardware stores.
To make your battery operated toy work with a single switch, you need to make a copper wafer that "interrupts" the flow of electricity from the battery to the motor, lights, or sound of the toy. You then plug your switch into the phone jack connected to the copper wafer. To activate the toy, you touch the switch and close the circuit of electricity, which causes to toy to turn on.
Any child who has difficulty accessing a standard battery operated toy's on/off button. For instance, a child may not be able to see the button, can not physically push the button, or developmentally does not understand the concept of cause and effect.
The first step in successfully adapting a toy is to choose an appropriate toy. The type of switch and the toy is determined by the individual needs of the child. Try different toys in the store to see how they work. The easiest toys to modify are ones that move in only one direction or use sound and lights as an activity. Choose toys with only one activity for your first project and try more complex toys as your expertise grows. Toys with multiple movements like spinning or flipping are more challenging to use with a switch because the wire has a tendency to become tangled and the battery interrupter can easily be pulled out. An alternative for toys where wires can get
tangled is a cordless Big Red Switch available from Ablenet (http://www.ablenetinc.com), which allows wireless activation. It also works well with toy trains, automobiles, and other toys that move about on the floor. Battery operated tape recorders and radios can also be modified, especially for older children where age appropriateness is an issue.
Never attempt to adapt an AC (Alternating Current) device (devices that plug into a standard 120 Volt wall outlet)
Adapt only DC (Direct Current) battery operated toys. When using a utility knife or covered blade to cut the wire make sure the wire is on a flat surface and you are cutting away from your body. Keep the hot end of the soldering gun and hot solder away from things that burn (including yourself!) and make sure your soldering iron is placed in its safety holder when not in use. Hot glue can also cause a bad burn so make sure the glue has cooled before touching any glued surface.
Battery operated toy
Switch (for testing & using the toy after adapting it)
22-24 gauge speaker wire / Radio Shack Part # 278-1385
1/8" phone jack / Radio Shack Part # 274-333
Circuit board (copper wafer) Radio Shack Part # 276-1499
Thinner circuit board may be desired and may be found at your local electronics store ( they may also be
able to direct you to local companies that use circuit boards that might be willing to give you their scrap
circuit board pieces)
Wire snips or shears
Hot glue gun / hot glue sticks
Metal file (optional)
Needle nose pliers
www.RadioShack.com or your local Radio Shack Store, other local electronics stores and some hardware stores.
For more accessible play ideas, please visit “We Can Play” at www.ataccess.orgPermission to copy for private or non-profit use only
There are 4 easy steps to adapting your battery operated toy for use with a switch.
1. Prepare the wire. Cut 22-24 gauge wire to desired length. The length will be determined by where the child will
be positioned to best activate the switch and be able to interact with the toy. Separate the tip of the wire into two
ends by cutting down the middle, like this:
2. Attach 1/8" phone jack to one end of wire. Strip plastic from the wire about 1/4" from the end. Unscrew plastic
cap of phone plug and slide over wire.
Fold or twist the wires back onto themselves to make them stronger.
Insert stripped wire ends into each hole in the metal prongs of the plug. Solder stripped wire ends onto each metal
prong making sure the wires do not touch each other. Take care so the jack cover will fit when the soldering is
done. File down solder to fit if necessary. Reattach jack cover by gently screwing the cover down until tight.
3. Make the copper wafer. Cut the copper wafer material to fit the end of the battery compartment using wire snips
or shears. Strip the wire and solder each piece of wire to opposite sides of the wafer making sure the two stripped
portions of the wires do not make contact. The idea is for the switch to complete the circuit. This is why it’s called a
4. Finishing the Job. Insert copper wafer between the battery and its contact point. You have now insulated the
battery from the toy’s on/off switch with the copper wafer. Now, the switch plugged into the 1/8" phone jack must be
closed in order to complete the circuit and turn on the toy! The original switch on the toy must be turned to the "on"
position. If the battery-interrupt device is working properly, the toy will not operate until the switch, which is plugged
into the 1/8" phone jack, has been turned on. Depending on the type of switch, the toy may operate only when the
switch is pressed or it may turn on with one press and off with another. The copper wafer must be properly aligned
inside the battery compartment of the toy. If the copper wafer fits too tightly you can remove the spring or compress
the spring using your needle nose pliers. As the copper wafer is prone to movement during play, a drop of hot glue
to affix the copper wafer in place will keep the toy in operation.